Thermo Scientific - Particle Size Analyzer PSM-500

Supplier: Thermo Fisher Scientific Australia Pty Ltd

Particle Size Analyzer PSM-500

1/3

The Particle Size Analyzer PSM-500 enables real-time, in-stream particle analysis for up to three material streams, optimising mineral recovery and process efficiency.

Provides accurate, real-time particle size analysis to enhance mineral recovery and process efficiency.

Key Features

Real-time, in-stream particle size analysis for up to three streams
Accurate feedback supports optimisation of grinding circuit performance
Rugged construction – ingress protection rating IP65, NEMA 4X corrosion resistance
Modern user interface and software with full colour local touch-panel
Higher bandwidth, field-replaceable transducers, no dilution required
Standard percentage of solids measurements
Improved alarms, status display, and reporting
No UPS or pumping required
Upgradable from PSM-400MPX

Benefits

Enhances mineral recovery with accurate particle size distribution and percent solids analysis
Increases energy efficiency in grinding control and throughput of minerals
Operates under harsh environmental conditions with temperature compensation
Easy calibration via the modern interface
Field-replaceable transducers reduce long-term costs and maintenance

Specifications

Density	2.0 to 5.5 SG for dry solids
Maximum Transport Diameter	<2.3 mm @ <1% retained by Wt. @ 2.7 SG, <1.2 mm @ <1% retained by Wt. @ 5.1 SG
Electrical Requirements	380/600 V, 50/60 Hz, 3 Phase
Electronic Connection	CAT5/6/6e network cable (max 100 m)
Enclosure Rating	IP65; CE; ICES 001, CSA, FCC Part 15B, RCM
Ambient Operating Temp.	-10°C to +50°C
Altitude Range	0 to 5000 m
Sample Type	Chemical: Caustic slurries up to pH 12.5
Particle Size Range	1 to 1000 microns (application dependent)
Solids Content	10% min to 60% max (wt), 3% min to 26% max (vol)
Update Time	Typically 10 seconds
Required Water Flow	45 L/min (measurement), 6–18 L/day (standardisation)
Manufacturing	Adelaide, ISO-9001:2000 certified
Pressure Range (Unit Air)	552–1034 kPa; Max flow: 17 m³/h @ 690 kPa
Water for Sampling	Min pressure: 276 kPa; Max pressure: 689 kPa; Flow: 45 L/min
Material (Wetted Parts)	Engineering polymers/rubber-coated steel
Coating	Commercial sandblast, primer, two-part epoxy finish
Vibrations	Max 10G at 20Hz
Unit Size	Each

Certifications & Quality Assurance

Manufactured in Adelaide facility, ISO-9001:2000 certified
CE, ICES 001, CSA, FCC Part 15B, RCM compliance

To contact Thermo Fisher Scientific Australia Pty Ltd about Thermo Scientific Particle Size Analyzer PSM-500 use Get a quote.

Key Features

Real-time, in-stream particle size analysis for up to three streams
Accurate feedback supports optimisation of grinding circuit performance
Rugged construction – ingress protection rating IP65, NEMA 4X corrosion resistance
Modern user interface and software with full colour local touch-panel
Higher bandwidth, field-replaceable transducers, no dilution required
Standard percentage of solids measurements
Improved alarms, status display, and reporting
No UPS or pumping required
Upgradable from PSM-400MPX

Benefits

Enhances mineral recovery with accurate particle size distribution and percent solids analysis
Increases energy efficiency in grinding control and throughput of minerals
Operates under harsh environmental conditions with temperature compensation
Easy calibration via the modern interface
Field-replaceable transducers reduce long-term costs and maintenance

Specifications

Density	2.0 to 5.5 SG for dry solids
Maximum Transport Diameter	<2.3 mm @ <1% retained by Wt. @ 2.7 SG, <1.2 mm @ <1% retained by Wt. @ 5.1 SG
Electrical Requirements	380/600 V, 50/60 Hz, 3 Phase
Electronic Connection	CAT5/6/6e network cable (max 100 m)
Enclosure Rating	IP65; CE; ICES 001, CSA, FCC Part 15B, RCM
Ambient Operating Temp.	-10°C to +50°C
Altitude Range	0 to 5000 m
Sample Type	Chemical: Caustic slurries up to pH 12.5
Particle Size Range	1 to 1000 microns (application dependent)
Solids Content	10% min to 60% max (wt), 3% min to 26% max (vol)
Update Time	Typically 10 seconds
Required Water Flow	45 L/min (measurement), 6–18 L/day (standardisation)
Manufacturing	Adelaide, ISO-9001:2000 certified
Pressure Range (Unit Air)	552–1034 kPa; Max flow: 17 m³/h @ 690 kPa
Water for Sampling	Min pressure: 276 kPa; Max pressure: 689 kPa; Flow: 45 L/min
Material (Wetted Parts)	Engineering polymers/rubber-coated steel
Coating	Commercial sandblast, primer, two-part epoxy finish
Vibrations	Max 10G at 20Hz
Unit Size	Each

Certifications & Quality Assurance

Manufactured in Adelaide facility, ISO-9001:2000 certified
CE, ICES 001, CSA, FCC Part 15B, RCM compliance

Read less...

To contact Thermo Fisher Scientific Australia Pty Ltd about Thermo Scientific Particle Size Analyzer PSM-500 use Get a quote.

psm-500-particle-size-analyzer-datasheet(0.21MB)

Let Thermo Fisher Scientific Australia Pty Ltd provide you with a quote

Supplier

Supplier: Thermo Fisher Scientific Australia Pty Ltd

Location: Scoresby, VIC

Trade With Confidence. The supplier of this item is approved as a Verified Supplier. Business registration, contact details and locations have been verified. Thermo Fisher Scientific Australia Pty Ltd are also proudly displaying these credentials:

Location:

Scoresby , VIC

Joined:

Sep 2026

Level:

Premium Storefront

Verified: