Pneumatic Vacuum Conveyor | VTEC
With capacities up to 9,000kg/hr and distances up to 30m it complements the larger Fresco pneumatic conveying systems. The V-Tec is ideally suited to the filling of packing machines, tablet presses, blenders, metering screw feeders and any other similar process systems.
It can handle powders, granules, tablets and any other sticky free or non free flowing material. The multi stage vacuum pump is powered by compressed air and generates vacuums up to -92kpa.
The V-Tec is ideally suited to hazardous dust areas where traditional electrical equipment is expensive and untidy. The inbuilt pneumatic control system allows for a free-standing unit which requires a single compressed air supply only.
Conveying, discharge and dwell times are easily set up by the operator using the three dial knobs in the control cabinet mounted on the side of the hopper. The cycle timing is adjusted during initial setup matching the product conveyed and the system through-put rate.
The V-Tec system can convey product from drums, 20-25kg bags, bulk bags or bag dump hoppers by utilising either a pickup wand or hopper charging adaptor. The conveying air flow can be manually adjusted to allow either lean or dense phase conveying.
This minimises product degradation and line wear while maximising system through-put. The conveying cycle is a cyclic process filling the hopper then discharging at preset intervals.
The tangential inlet transition causes a cyclonic effect on the incoming product separating the product and conveyed air. The air then passes through the filter, multistage vacuum pump and out to atmosphere.
The hopper exhaust valve opens discharging product into the downstream process below. The system continues until a signal is received closing the supply pneumatic air solenoid valve.
The V-Tec hopper loaders weigh from 10-36kg making them extremely light and transportable. Each unit can be easily dismantled into smaller more manageable sections allowing ease of relocation and cleaning by a single operator.
The side mounted quick release clips provide extremely fast access and reassembly to all sections of the V-Tec hopper loader. Silicon seals ensure hygienic sealing between each section.
Electric or compressed air operated units are available with booster kits if conveying difficult to handle materials. With integral controls the Vtec is a plug and play unit that can be easily dismantled for cleaning.
VTEC Vacuum Conveyor Features include:
To contact Fresco Systems Australasia about Pneumatic Vacuum Conveyor | VTEC use Get a quote.
With capacities up to 9,000kg/hr and distances up to 30m it complements the larger Fresco pneumatic conveying systems. The V-Tec is ideally suited to the filling of packing machines, tablet presses, blenders, metering screw feeders and any other similar process systems.
It can handle powders, granules, tablets and any other sticky free or non free flowing material. The multi stage vacuum pump is powered by compressed air and generates vacuums up to -92kpa.
The V-Tec is ideally suited to hazardous dust areas where traditional electrical equipment is expensive and untidy. The inbuilt pneumatic control system allows for a free-standing unit which requires a single compressed air supply only.
Conveying, discharge and dwell times are easily set up by the operator using the three dial knobs in the control cabinet mounted on the side of the hopper. The cycle timing is adjusted during initial setup matching the product conveyed and the system through-put rate.
The V-Tec system can convey product from drums, 20-25kg bags, bulk bags or bag dump hoppers by utilising either a pickup wand or hopper charging adaptor. The conveying air flow can be manually adjusted to allow either lean or dense phase conveying.
This minimises product degradation and line wear while maximising system through-put. The conveying cycle is a cyclic process filling the hopper then discharging at preset intervals.
The tangential inlet transition causes a cyclonic effect on the incoming product separating the product and conveyed air. The air then passes through the filter, multistage vacuum pump and out to atmosphere.
The hopper exhaust valve opens discharging product into the downstream process below. The system continues until a signal is received closing the supply pneumatic air solenoid valve.
The V-Tec hopper loaders weigh from 10-36kg making them extremely light and transportable. Each unit can be easily dismantled into smaller more manageable sections allowing ease of relocation and cleaning by a single operator.
The side mounted quick release clips provide extremely fast access and reassembly to all sections of the V-Tec hopper loader. Silicon seals ensure hygienic sealing between each section.
Electric or compressed air operated units are available with booster kits if conveying difficult to handle materials. With integral controls the Vtec is a plug and play unit that can be easily dismantled for cleaning.
VTEC Vacuum Conveyor Features include:
To contact Fresco Systems Australasia about Pneumatic Vacuum Conveyor | VTEC use Get a quote.
Thanks for your help!
Sorry! Unable to submit your request at this time. Please try again later.
Report this product